Section 4.3
Rigid liferafts
Chapter IVPage 2214 clauses
This content comes from OCR text extraction
The text may contain inaccuracies, especially units and clause numbers. Treat the original scanned pages or the official IMO document as authoritative.
4.3.1Rigid liferaits shall comply with the requirements of section 4.1 and, in addition, shall comply with the requirements of this section.
4.3.2Construction of rigid liferafts
4.3.2.1The buoyancy of the literaft shall be prowded by approved inherently buoyant material placed as near as possible to the periphery of the liferait. The buoyant material shall be fire-retardant or be protected by a fire-retardant covering.
4.3.2.2The floor of the liferaft shall prevent the ingress of water and shall effectively support the occupants out of the water and insulate them from cold.
4.3.3Carrying capacity of rigid liferafts BS The number of persons which a liferaft shall be geeene eenodahe al be equal to the lesser of Jl the greatest whole number obtained by dividing by 0.096 the volume, measured in cubic metres, of the buoyancy material multiplied by a factor of 1 minus the specific gravity of that material; or ue 2 the greatest whole number r dividing by 0.372 the horizontal cross-sectional area of the floor of the liferaft measured in metres; or 3 the number of persons having an average mass of 82.5 kp, all wearing immersion suits and litejackets, that can be seated with sufficient combort and headroom without interfering with the operation of any of the liferaft's equipment.
4.3.4Access into rigid liferaits
4.3.4.1At least one entrance shall be fitted with a boarding ramp, capable of supporting a person weighing 100 ke sitting or kneeling and not holding onto any other part of the literait, to enable persons to board the liferait trom the sea. In the case of a davit-launched liferalt having more than one entrance, the boarding ramp shall be fitted at the entrance opposite to the bowsing and embarkation facilitres.
4.3.4.2Entrances not provided with a boarding ramp shall have a boarding ladder, the lowest step of which shall be situated not less than 0.4 m below the liferait’s light waterline.
4.3.4.3There shall be means inside the liferaft to assist persons to pull themselves into the liferalt from the lacider.
4.3.5Stability of rigid liferafts
4.3.5.1Unless the liferait ts capable of operating safely whichever way up it is floating, its strength and stability shall be such that it is either seli-righting or can be readily nghted in a seaway and in calm water by One person.
4.3.5.2The stability of a liferaft when loaded with its full complement of persons and equipment shall be such that it can be towed at speeds of up to 3 knots in calm water.
4.3.6Markings on rigid liferafts The fileraft shall be marked with: name and port of registry of the ship to which it belongs; 2 maker's name or trademark; 3 sefial number, 4 name of approving authority; 46 number of persons it is permitted to accommodate over each entrance in characters not less than 100 mm in height of a colour contrasting with that of the iferatt; 6 SOLAS; 7 type of emergency pack enclosed: length of painter; 4 = maximum permitted height of stowage above waterline (drop-test height); and 10) launching instructions.
4.3.7Davit-launched rigid liferafts In addition to the above requirements, a rigid liferaft for use with an approved launching appliance shall, when suspended from its lifting hook or bidle, withstand a load of four times the mass of its full complement of persons and equipment. S 44 General requirements for lifeboats’ 4.4.1 Construction of lifeboats we 441.1 All lifeboats. shill be: properly consffeeied and shall be of such form and proportions that they have ample stability in a seaway and sufficient freeboard when loaded with their full complement of persons and equipment, and are capable of being safely launched under all conditions of trim of up to 10° and list of up to 207 either way. All lifeboats shall have rigid hulls and shall be capable of maintaining positive stability when in an upright position in calm water and boacded with their full complement of persons and equipment and holed in.any one locahon below the waterline, assuming no loss of buoyancy material and no other damage. 4.4.1.2 Each lifeboat shall be fitted with a permanently affteed approval plate, endorsed by the Administration of its representative, contamung at beast the following items: Joos manuiacturer’s name and address: 2 lifeboat model and serial number: 23 = month and year of manuiacture; 4 number of persons the lifeboat is approved to carry; and 6 the appreval information required under paragraph 1.2.2.9. Each production hiteboat shall be provided with a certihcate or declaration of conformity which, in addition to the above items, specifies: 6 = number of the certificate of approval; 7 material of bull construction, in such detail as to ensure that compatibility problems in repair should not occur, 8 total mass fully equipped and fully manned; 9% = the measured towing force of the lifeboat; and 10) statement of approval as to sections 4.5, 4.6, 4.7, 4.8 or 4.9.